Hi, comrades! We use the linux version of TopSpin 2.1 as a software for AVANCE II Bruker 400 MHz.As I found parameters of pulse sequences are located in /opt/topspin/exp/stan/nmr/par - directory.
I've started to study the content of "acqu" - file in directory /opt/topspin/exp/stan/nmr/par/PROTON and couldn't find any definitions of some parameters in Bruker-manuals. For instance, DBL, DATE, DBP, DBPNAME[0-7], DECBNUC, DECNUC, DECSTAT, DL, DP, DPO.
Where can I find the meaning and explanation of that parameters?
Check if somebody has answered this question on NMRWiki QA forum
Did you find this post helpful? |
Similar Threads
Thread
Thread Starter
Forum
Replies
Last Post
[Question from NMRWiki Q&A forum] Editing solvent parameters on vnmrj?
Editing solvent parameters on vnmrj?
The default parameter setting for Acetic Acid seems to be setting the Lock Power to two. This is a problem when running our automated robot runs. Where do I find the file to edit this to an appropriate setting?
Thanks
Check if somebody has answered this question on NMRWiki QA forum
nmrlearner
News from other NMR forums
0
05-23-2012 04:23 PM
[Question from NMRWiki Q&A forum] adjusting topshim parameters
adjusting topshim parameters
On our Avance III 500 we use Topshim quite successfully for any probe with a gradient coil. The only time we have a problem is with CDCl3 solvent on our 1.7 mm TXI probe, where Topshim fails with a complaint about the signal to noise ratio being too low. This is not surprising for a microprobe, as CDCl3 has the lowest signal of any common deuterated solvent. We have confirmed that the 2H pulse length is correct in the prosol file.
An obvious solution would be to increase the nunber of scans for this probe/solvent combination. There seem to be probe and...
nmrlearner
News from other NMR forums
0
07-25-2011 11:01 AM
[Question from NMRWiki Q&A forum] same parameters but difference in phase why?
same parameters but difference in phase why?
hi, though this question seems to be easy for you but i am new for this software and to this field. Recently, i took silicon spectra in 500mhz(bruker) seems to be good (i.e.one silicon peak and one nmr tubes broad peak) but when i used same parameters for another sample where i got single peak as i expected but nmr tube peak is inverse this time. I just copied previous parameters only why i got such a inverse signal.If anybody know please help me.
thank you
Check if somebody has answered this question on NMRWiki QA forum
[NMR paper] Determination of protein structures consistent with NMR order parameters.
Determination of protein structures consistent with NMR order parameters.
Related Articles Determination of protein structures consistent with NMR order parameters.
J Am Chem Soc. 2004 Jul 7;126(26):8090-1
Authors: Best RB, Vendruscolo M
Order parameters obtained from NMR experiments characterize distributions of bond vector orientations. Their interpretation, however, usually requires the assumption of a particular motional model. We propose a multiple-copy simulation method in which the experimental order parameters are used as restraints in...
nmrlearner
Journal club
0
11-24-2010 09:51 PM
[NMR paper] Changes in the NMR-derived motional parameters of the insulin receptor substrate 1 ph
Changes in the NMR-derived motional parameters of the insulin receptor substrate 1 phosphotyrosine binding domain upon binding to an interleukin 4 receptor phosphopeptide.
http://www.ncbi.nlm.nih.gov/corehtml/query/egifs/http:--pubs.acs.org-images-acspubs.jpg Related Articles Changes in the NMR-derived motional parameters of the insulin receptor substrate 1 phosphotyrosine binding domain upon binding to an interleukin 4 receptor phosphopeptide.
Biochemistry. 1997 Apr 8;36(14):4118-24
Authors: Olejniczak ET, Zhou MM, Fesik SW
Proteins recognize...
nmrlearner
Journal club
0
08-22-2010 03:31 PM
[NMR paper] Changes in the NMR-derived motional parameters of the insulin receptor substrate 1 ph
Changes in the NMR-derived motional parameters of the insulin receptor substrate 1 phosphotyrosine binding domain upon binding to an interleukin 4 receptor phosphopeptide.
http://www.ncbi.nlm.nih.gov/corehtml/query/egifs/http:--pubs.acs.org-images-acspubs.jpg Related Articles Changes in the NMR-derived motional parameters of the insulin receptor substrate 1 phosphotyrosine binding domain upon binding to an interleukin 4 receptor phosphopeptide.
Biochemistry. 1997 Apr 8;36(14):4118-24
Authors: Olejniczak ET, Zhou MM, Fesik SW
Proteins recognize...
nmrlearner
Journal club
0
08-22-2010 03:03 PM
Script to obtain order parameters from a structure
A Python script for prediction of order paramter from a structure is available from this website.
The script is based on the following paper
F. Zhang and R. Brüschweiler (2002) "Contact Model for the Prediction of NMR N-H Order Parameters in Globular Proteins" J. Am. Chem. Soc. 124(43), 12654-12655.
File with discription of parameters
Linear Mode
